ChiTu L V3
ChiTu L V3
ChiTu L V3

ChiTu L V3 Board For Mono Screen mSLA/LCD 3D Printer

$85.00 USD $54.14 USD
Free shipping on all orders in mainstream countries

Touch screen Size: 2.8 inch

2.8 inch
3.5 inch
4.3inch
5.0 inch
only board

Firmware Option: 5.96 Mono

5.96 Mono
6.08 Mono
FHD 5.5 Mono
Sharp04

visamasterpaypalamerican expressapple payjcb
Description

SLA Controller Board ChiTu L 5.5 V3  For Creality LD-002R Printer With 32Bit ChiTu System For LCD 3D Printer Motherboard

The firmware option is FPGA firmware come with board, you can also update yourself from our download page

 


WITH DXQ608-X04 6.08 inch MONO LCD



WITH RV059FBB-N80 5.96 inch MONO LCD



WITH LS055R1SX04 5.5 inch RBG LCD


Parameters:

Mainboard size：120*85mm

Microprocessors：STM32F407(168Hz)

Input voltage:12~24V 5~15A

Motor driver：Allegro A4988(2 extended signal)

Color touch screen：2.8/3.5/4.3/5.0 inch TFT color touch screen

Supported LCD screen：5.5inch /6.08inch monochrome 2k

Data interface:U disk,Network port,WIFI

Supported file format: ctb

Interface type：MIPI

Slice software：CHITUBOX

 

Shipping list：

1.only board： controller board + gifts

2. controller board + 2.8/3.5/4.3/5.0 touch screen + 50cm FFC cable + gifts

Notice:

The touch screen can only be used for ChiTu controller board.Other screens may not match ChiTu controller board.

ChiTuL5.5 V3 is our major board for small size monochrome LCD, it supports different version of 

*Support DXQ 6.08 inch monochrome LCD resin panel 1620*2560(ZX608XI5249727/DXQ608-X04)

*Support Duobond 5.96 inch monochrome LCD resin panel 1620*2560（RV059FBB-N80）


Chitusystems compatibility chart

 

Screen Interface V1 V2 V3 K1 H1
5.5‘’-RGB-1440*2560 MIPI/03 ●
5.5‘’-RGB-1440*2560 MIPI/04 ● ● ●
5.5‘’-RGB-2160*3840 MIPI ●
5.5‘’-MONO-1080*1920 MIPI ● ● ●
5.96‘’-MONO-1620*2560 MIPI ● ●
6.0‘’-RGB-1440*2560 MIPI ●
6.08‘’-MONO-1620*2560 MIPI/04 ● ●
6.23‘’-MONO-3840*2400 MIPI ● ●
8.9‘’-RGB-2560*1600 MIPI ●
10.1‘’-RGB-2560*1600 MIPI ●
12.5‘’-RGB-3840*2160 eDP ●
13.3‘’-RGB-3840*2160 eDP ●
15.6‘’-RGB-3840*2160 eDP ●



Notice

Installing power supply：

As shown below, connect the power supply wire with -12V/24V+ port.

Please note: reverse connection of the positive and negative poles will make damage to the motherboard !!!

 

You can also Click here  to find out the difference between Mono LCD and RGB LCD.







 

The V3 board can only work with X04 port LCD, please DO NOT connect sharp03 or DXQ608-03 with it, it will damage the board U3 chip.


If your Z-axis direction is not right, you can edit the parameter file M8004 to fix it,

Or print this file we edited for you directly, and download it here.